Florida mechanical contractor candidate studying trade exam practice questions with fuel gas and mechanical code books

Florida Mechanical Contractor Practice Test: Trade Exam Quiz

Prepare with 7 Florida mechanical contractor exam prep quiz questions on piping, boilers and HVAC systems, plus free License Fix portal access.

Pascual, Contractor Licensing Instructor
October 23, 2026 • 8 min read

Strong Florida mechanical contractor exam prep starts with understanding why the Certified Mechanical Contractor (CMC) exam is one of the longest and broadest trade tests in the state. Like Class A air conditioning, the Mechanical Trade Knowledge exam runs 7.5 hours with 130 scored questions at Pearson VUE, but its statutory scope adds fuel transmission lines, medical and chemical piping, lift stations, standpipes, and gasoline tanks. Every figure below was checked against Florida Statutes Section 489.105 and Rule 61G4-16.001, Florida Administrative Code in October 2026. Test your readiness with the seven original study practice questions below (not copied from the confidential state exam).

What Does the Florida Mechanical Trade Knowledge Exam Cover?

The Florida mechanical trade knowledge exam consists of 130 equally weighted multiple choice questions administered over 7.5 hours on a computer at Pearson VUE, requiring at least 91 correct answers (70 percent) to pass. Under Rule 61G4-16.001, the content weights reflect both unlimited HVAC work and specialty piping:

  • Installation of mechanical systems: 14 percent (about 18 questions)
  • Installation of mechanical equipment and components: 14 percent (about 18 questions)
  • Installation of refrigeration and HVAC systems: 12 percent (about 16 questions)
  • Pre installation and design engineering: 9 percent (about 12 questions)
  • Ductwork and HVAC materials: 9 percent (about 12 questions)
  • Safety and equipment: 9 percent (about 12 questions)
  • Maintenance, controls, energy management, and excavating (2 percent): remaining 33 percent

For a complete breakdown of licensing requirements, read our Florida mechanical contractor license guide.

Stainless steel pressure gauges, brass valves, mechanical blueprints, and a tabbed code binder on a contractor desk

How Does a Florida Mechanical Contractor License Compare to Class A HVAC?

Candidates pursuing a Florida mechanical contractor license often ask what the CMC classification allows beyond an unlimited Class A air conditioning license. Under Florida Statutes Section 489.105(3)(i), a mechanical contractor has all the unlimited central air conditioning, refrigeration, heating, ventilation, boiler, and pressure vessel privileges of Class A, plus an expanded piping scope.

  • Mechanical contractors may install, maintain, repair, fabricate, alter, extend, or design lift station equipment and piping, gasoline tanks and pump installations, and fire standpipes.
  • The scope also includes air piping, vacuum line piping, oxygen lines, nitrous oxide piping, ink and chemical lines, fuel transmission lines, and liquefied petroleum (LP) and natural gas fuel lines within buildings.
  • However, a mechanical contractor still may not install potable water lines, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring.
  • For candidates using the college degree route, the board rule specifies a four year Mechanical Engineering degree plus one year of proven experience.

CMC License Exam Prep: Questions 1 and 2 (Scope & Boilers)

Work through these first two CMC license exam prep questions covering statutory boundaries and boiler safety controls.

  • Question 1 (Mechanical Scope): Under Section 489.105(3)(i), which installation may a Certified Mechanical Contractor perform without subcontracting? A) Potable water distribution risers. B) Gasoline tanks, pumps, oxygen lines, and natural gas lines within a building. C) Sanitary sewer drains. D) Pool filtration piping.
  • Answer 1: B. Section 489.105(3)(i) grants authority over gasoline tanks, oxygen and nitrous oxide lines, vacuum and air piping, lift station piping, and LP/natural gas lines inside buildings, while excluding potable water, sewer, and pool piping.
  • Question 2 (Boiler Safety): Under FBC Mechanical Section 1007, what safety device is required on hot water heating boilers to prevent operation when water drops below the safe level? A) Draft damper. B) Automatic low water fuel cutoff. C) Blowdown valve. D) Flow switch.
  • Answer 2: B. Section 1007 requires an automatic low water cutoff that stops the fuel or energy supply.

Mechanical Contractor License Florida Quiz: Questions 3 and 4 (Pumps & Fuel Gas)

When studying for a mechanical contractor license Florida exam, expect questions on pump laws and gas testing.

  • Question 3 (Pump Affinity): If pump speed rises from 1,200 to 1,800 RPM (1.5x), how does flow (GPM) change per the first Affinity Law? A) Drops 33 percent. B) Rises directly with speed (1.5x). C) Rises by speed squared (2.25x). D) Rises by speed cubed (3.375x).
  • Answer 3: B. Flow varies directly with speed (1.5x), head with the square (2.25x), and power with the cube (3.375x).
  • Question 4 (Gas Testing): Under 2023 FBC Fuel Gas Sections 406.4.1 and 406.4.2, a low pressure single family gas test must hold at least: A) 1/2 psi. B) 1.5x maximum working pressure (minimum 3 psig) for at least 10 minutes. C) 100 psig. D) Oxygen test.
  • Answer 4: B. Sections 406.4.1 and 406.4.2 require 1.5x working pressure (minimum 3 psig) for at least 10 minutes on single family systems (or 30 minutes per 500 cubic feet).

Florida Mechanical Contractor Exam Prep: Questions 5 and 6 (OSHA & Hydronics)

This Florida mechanical contractor exam prep section covers OSHA trench egress (2 percent of the exam) and hydronic math.

  • Question 5 (OSHA Egress): In a fuel line trench, at what depth does OSHA 29 CFR 1926.651(c)(2) require a ladder or ramp within 25 feet of lateral travel? A) 2 feet. B) 4 feet or more. C) 5 feet. D) 8 feet.
  • Answer 5: B. OSHA 1926.651(c)(2) requires egress within 25 feet of travel in trenches 4 feet or deeper.
  • Question 6 (Hydronic Math): A chilled water cooling coil receives 80 GPM entering at 44 degrees F and leaving at 54 degrees F. Using Qt = 500 times GPM times Delta T, what cooling is delivered? A) 200,000 Btuh. B) 400,000 Btuh (33.3 tons). C) 480,000 Btuh. D) 600,000 Btuh.
  • Answer 6: B. Water warms from 44 to 54 degrees F (10 degree Delta T); 500 times 80 times 10 = 400,000 Btuh (33.3 tons).

Question 7 and How to Score Your Mechanical Practice Run

Ventilation intake separation rules in FBC Mechanical Chapter 4 appear frequently on the 130 question trade test.

  • Question 7 (Mechanical Ventilation Intakes): Under FBC Mechanical Chapter 4, outdoor air intake openings for mechanical ventilation systems must be located a minimum of how many feet horizontally from any contaminant source such as a plumbing vent or exhaust outlet? A) 2 feet. B) 3 feet. C) 10 feet. D) 25 feet.
  • Answer 7: C. Outdoor air intakes must be located at least 10 feet horizontally from contaminant sources such as plumbing vents and exhaust outlets, unless specific vertical separation exceptions apply.
  • Scoring Your Run: Reaching 5 out of 7 (71 percent) matches the 70 percent threshold (91 out of 130 questions) required to pass the Florida Mechanical Trade Knowledge exam.

Tabbed 2023 Florida Building Code book, scale ruler, and scientific calculator on a study desk

Frequently Asked Questions (FAQ)

How long is the Florida Mechanical Contractor Trade Knowledge exam?

The Florida Mechanical Trade Knowledge exam has 130 scored multiple choice questions and a 7.5 hour time limit at Pearson VUE. It is an open book exam requiring a minimum score of 70 percent (91 correct answers). Candidates also pass the 120 question Business and Finance exam.

What is the difference between a Florida Mechanical Contractor and a Class A HVAC Contractor?

Both licenses allow unlimited central air conditioning, refrigeration, heating, ventilation, and boiler work. The Certified Mechanical Contractor (CMC) license adds lift station equipment and piping, gasoline tanks and pumps, fire standpipes, medical and chemical piping, and LP/natural gas lines within buildings.

Can a Mechanical Contractor install potable water or sewer lines in Florida?

No. Under Florida Statutes Section 489.105(3)(i), potable water lines and connections, sanitary sewer lines, swimming pool piping and filters, and electrical power wiring are excluded from the mechanical scope and must be subcontracted to a contractor licensed in that trade.

How can I get free Florida mechanical contractor practice questions?

Practice with the seven worked questions on this page, then register for a free student account on our Free Course page. Your free registration requires no credit card and unlocks the License Fix Student Portal and introductory Business and Finance training.

Start Your Florida Mechanical Contractor Exam Prep for Free Today

Answering seven practice questions gives you a clear view of how our Florida mechanical contractor exam prep combines HVAC math, hydronic piping, fuel gas codes, and OSHA rules. To take the next step, create your free student account today at our Free Intro to Business and Finance Course page with no credit card required. Inside your free account, you get instant access to the License Fix Student Portal on computer or mobile, video lessons for the mandatory Business and Finance exam, and extra free contractor practice test questions. When you are ready to prepare for the 7.5 hour trade exam, enroll in our self paced Florida Mechanical Trade Exam Preparation Course, available in English and Spanish.

Pascual, Contractor Licensing Instructor

About Pascual, Contractor Licensing Instructor

Contractor Licensing Instructor

Pascual is a Florida contractor licensing exam prep specialist, with a focus on the Business & Finance and General Contractor exams. He has helped numerous candidates prepare for and pass their state exams, combining technical knowledge of Florida's regulations with practical study strategies. His approach is straightforward and grounded in real experience with the exam format, helping future contractors understand not just the content, but also how to avoid the most common mistakes that trip up candidates.

Contact Us Today