
Florida Plumbing Exam Practice Test: Quiz & Isometric Tips
Try 7 practice plumbing exams questions for Florida CFC candidates, including isometric drawing tips and code lookups. Register free today.
Working through practice plumbing exams is essential for anyone pursuing a Certified Plumbing Contractor (CFC) license in Florida, because plumbing is the only state construction trade exam still administered on paper with hand drawn isometric diagrams. While candidates take the Business and Finance exam on a computer at Pearson VUE, the Plumbing Trade Knowledge exam requires you to answer 110 multiple choice questions and complete five isometric drawings worth up to 10 points each. Every figure below was checked against Florida Statutes Section 489.105 and Rule 61G4-16.001, Florida Administrative Code in October 2026. Answer the seven original practice questions below (created for study practice and not copied from the confidential state exam) to test your code navigation.
How Are Florida Plumbing License Exams Scored?
A Florida plumbing license candidate must pass two separate examinations: the computer based Business and Finance exam (120 questions in 6.5 hours) and the paper and pencil Plumbing Trade Knowledge exam. According to the DBPR construction examination overview and Rule 61G4-16.001, the trade exam has 160 total possible points and requires at least 112 points (70 percent) to pass:
- Sanitary and storm drainage systems: 20 percent
- Water distribution systems: 20 percent
- Medical gas piping systems: 20 percent
- Natural gas piping systems: 15 percent
- Industrial piping systems: 10 percent
- Swimming pools, wells, and irrigation: 5 percent
- Solar heating water systems: 5 percent
- Fire protection systems: 5 percent
Notice that medical gas, natural gas, and industrial piping combine for 45 percent of the written exam. Read our Florida plumbing license applicant guide for full application details.

How Are the Plumbing Isometric Drawings on the Florida Exam Graded?
On the plumbing isometric drawings exam Florida candidates take on paper, five drawings are worth up to 10 points each (50 points total), and the candidate booklet warns that you cannot reach the 112 point passing score on multiple choice questions alone. Even if you answered all 110 multiple choice questions correctly, you would have 110 points, which is two points short of passing.
- Each isometric drawing is evaluated independently by three qualified graders, and at least two of the three graders must agree on each scoring criterion.
- Drawings must be plotted on 30-60-90 degree isometric axes using the provided straightedge and symbols.
- Graders award the highest weight to correct pipe orientation and piping layout, followed by proper venting, flow direction and fixture connections, legibility and 30 degree angles, and pipe size labeling.
- Always practice drawing residential and commercial bathroom groups, wet vents, and roof vent terminations before exam day.
Plumbing License Practice Test: Questions 1 and 2 (Scope & Drainage Slope)
Use this plumbing license practice test set to check statutory scope and drainage slope under FBC Plumbing.
- Question 1 (Statutory Scope): Under Florida Statutes Section 489.105(3)(m), which system is included in a Certified Plumbing Contractor's scope? A) High voltage wiring to a well pump. B) Medical gas, LP and natural gas lines, storm drainage, and solar water heating. C) Structural concrete roof decks. D) Central AC air handlers over 25 tons.
- Answer 1: B. Section 489.105(3)(m) includes sanitary and storm drainage, water supply, septic tanks, wells, pool piping, irrigation, solar water heating, gas lines, and medical gas.
- Question 2 (Drainage Slope): Under FBC Plumbing Chapter 7, what is the minimum slope for horizontal drainage piping 2.5 inches or less in diameter? A) 1/16 inch per foot. B) 1/8 inch per foot. C) 1/4 inch per foot. D) 1/2 inch per foot.
- Answer 2: C. Horizontal drainage piping 2.5 inches or smaller requires a minimum slope of 1/4 inch per foot.
Florida Plumbing Exam Preparation: Questions 3 and 4 (Backflow & Medical Gas)
Strong Florida plumbing exam preparation covers water protection and NFPA 99 medical gas rules (40 percent of the test).
- Question 3 (Air Gaps): Under 2023 FBC Plumbing Section 608.16.1 and Table 608.16.1, a fixture air gap away from walls must be at least: A) Equal to the opening diameter. B) Twice the effective opening diameter (subject to Table 608.16.1 minimums, or 3x near walls). C) 1/4 inch. D) Irrigation only.
- Answer 3: B. Section 608.16.1 and Table 608.16.1 require twice the effective opening diameter away from walls (3x near walls), never below the table minimum.
- Question 4 (Medical Gas): Under NFPA 99, what brazing alloy and purge gas join copper medical gas piping? A) 50/50 solder. B) BAg with flux. C) BCuP alloy (no flux on copper to copper) with oil free dry nitrogen purge. D) Solvent cement.
- Answer 4: C. Copper medical gas joints use BCuP alloys without flux under a dry nitrogen purge.
Practice Plumbing Exams: Questions 5 and 6 (Fuel Gas & Isometrics)
This section of our practice plumbing exams covers fuel gas sediment traps (15 percent of the exam) and isometric grading criteria.
- Question 5 (Sediment Traps): Under FBC Fuel Gas Chapter 4, where a sediment trap is required at an appliance gas connection, where must it be installed? A) Upstream of the shutoff valve. B) Downstream of the appliance shutoff valve as close to the inlet as practical. C) At the meter. D) Inside the burner.
- Answer 5: B. A sediment trap goes downstream of the shutoff valve near the inlet, except for ranges, dryers, and outdoor grills.
- Question 6 (Isometric Criteria): On the five isometric drawings, which combination carries the heaviest grading weight under Rule 61G4-16.001? A) Artistic shading. B) Orientation, piping layout, and venting. C) Contractor name on every pipe. D) Three dimensional perspective.
- Answer 6: B. Orientation and piping carry the most weight, followed by vents, flow and fixtures, legibility and 30-60-90 degree angles, and labeling.
Question 7 and How to Score Your Plumbing Practice Run
Pipe fall math appears regularly on the exam and rewards candidates who verify every unit conversion before selecting an answer.
- Question 7 (Pipe Fall Math): A 4 inch building sewer runs 120 feet from the building drain connection (invert elevation 98.50 feet) to the public manhole at a uniform slope of 1/8 inch per foot. What is the invert elevation at the manhole connection? A) 96.00 feet. B) 97.25 feet. C) 97.50 feet. D) 99.75 feet.
- Answer 7: B. At 1/8 inch (0.125 inches) per foot over 120 feet, total fall is 120 times 0.125 equals 15 inches, which is 1.25 feet. Subtract 1.25 feet from 98.50 feet to get 97.25 feet.
- Scoring Your Run: Reaching 5 out of 7 (71 percent) matches the 70 percent threshold required on the 160 point Florida plumbing exam. Always practice plotting isometric drawings alongside written questions.

Frequently Asked Questions (FAQ)
Why is the Florida plumbing trade exam still taken on paper?
The Florida Plumbing Trade Knowledge exam includes five hand drawn isometric plumbing diagrams that must be plotted with a straightedge and scored by three human graders. Because of those five drawings, the trade portion is offered on paper six times a year, while Business and Finance is computer based.
How many points do I need to pass the Florida plumbing exam?
The Plumbing Trade Knowledge exam has 160 total possible points: 110 multiple choice questions worth one point each plus five isometric drawings worth up to 10 points each. You must earn at least 112 points (70 percent) to pass, which requires scoring points on the isometric drawings.
When is the Florida plumbing trade exam offered each year?
Unlike computer based exams offered daily at Pearson VUE, the paper Plumbing Trade Knowledge exam is normally administered six times a year in February, April, June, August, October, and December. Your examination application must be submitted at least 30 days before the scheduled exam window.
How can I start studying with free practice plumbing exams?
Start with the seven worked questions on this page, then sign up for a free student account on our Free Course page. You will get instant access to the License Fix Student Portal, foundational Business and Finance training, and practice questions at zero cost.
Start Your Free Florida Plumbing Exam Prep Course Today
Solving seven sample questions in practice plumbing exams shows how the state tests code lookups and math, but mastering both the 110 written questions and the five isometric drawings takes guided practice. You can create your free student account today on our Free Intro to Business and Finance Course page with no credit card required. Your free sign up unlocks the License Fix Student Portal on computer or mobile, video exam walkthroughs, and extra free contractor practice test questions. To master isometric drawings, medical gas, and FBC Plumbing chapters step by step, check out our complete Florida Plumbing Trade Exam Preparation Course.

About Pascual, Contractor Licensing Instructor
Contractor Licensing Instructor
Pascual is a Florida contractor licensing exam prep specialist, with a focus on the Business & Finance and General Contractor exams. He has helped numerous candidates prepare for and pass their state exams, combining technical knowledge of Florida's regulations with practical study strategies. His approach is straightforward and grounded in real experience with the exam format, helping future contractors understand not just the content, but also how to avoid the most common mistakes that trip up candidates.
More from Pascual, Contractor Licensing Instructor